Форум по автодиагностике, автосканерам, ремонту, обслуживанию и эксплуатации автомобилей

Форум по автодиагностике, автосканерам, ремонту, обслуживанию и эксплуатации автомобилей (http://autoprogs.ru/index.php)
-   Диагностика Chrysler / Jeep / Dodge | ремонт электроники (http://autoprogs.ru/forumdisplay.php?f=298)
-   -   Dodge Ram (http://autoprogs.ru/showthread.php?t=5095)

Furg0n 03.09.2014 08:53

Тогда есть вероятность, что другие протоколы не выведены на OBD-II?

С уважением!

Furg0n 03.09.2014 08:56

CCD это же в приборную панель информацию с движка гонит?

Juan7 03.09.2014 08:58

RE: Dodge Truck and Jeep - Engine Control Modules supporting both SAE J1850 and ISO 9141-2 Protocols.
Chrysler LLC has determined that certain Dodge truck and Jeep vehicles have an engine control module (ECM) that will respond and communicate to generic scan tools or Inspection and Maintenance (I/M) equipment with either SAE J1850 (10.4 VPW) or ISO 9141-2 (K-line). These vehicles were intended to exclusively support J1850 however the earlier K-line protocol support was mistakenly not disabled. These ECMs will communicate on whichever protocol is tried first. The same OBD information (e.g., readiness status, fault codes, commanded MIL status, etc.) is available from the ECM on either protocol.
The “dual protocol” support may cause an issue in I/M where programs are expecting a specific protocol to be supported for these vehicles and/or comparing the supported protocol with other like vehicles or past inspection records of the exact same vehicle (e.g., for fraud detection). The protocol used will depend on the order which the inspection equipment cycles through the different protocols during initialization as well as when in the process the inspector connected the equipment.

Dodge Truck Applications with "JTEC" ECM communicating on both J1850 & ISO9141-2
2003
Ram Pickup
3.7L V6, 5.9L V8

Juan7 03.09.2014 09:03

ELM327 должен работать с этим протоколом ....

Juan7 03.09.2014 09:09

Цитата:

Сообщение от Furg0n (Сообщение 179964)
CCD это же в приборную панель информацию с движка гонит?

о CCD Bus знаю только :
Transmission media - Twisted Pair
Speed - 7,812.5 bps
Bus Bias required - Yes
Maximum No of Modules - 13
Note: CCD bus is no longer used on any current production vehicles.

Juan7 03.09.2014 09:12

Если есть VIN .... то я могу посмотреть более конкретно схему

Furg0n 03.09.2014 09:15

VIN могу вечером только скинуть.
Двигатель 5.9L V6 ISB disel, 235hp, Common Rail

Я уже писал, что читатели ошибок в виде Автоком, ЕЛМ и прочее не рассматриваются :-)

С уважением!

Furg0n 03.09.2014 09:20

Juan7

Посмотрите личку

Juan7 03.09.2014 09:21

Вложений: 2
посмотел recall на этот трак ...

Juan7 03.09.2014 09:23

Вложений: 1
Позвонить можно .... но я живу в Штатах ...
еще один recall о ЕСМ


Текущее время: 00:44. Часовой пояс GMT +3.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc. Перевод:
zCarot
Автодиагностика и автосканеры.