Semen84

Спасибо за подсказку.
Хочу добавить: Если смотреть эти параметры в ДевТуле на базах серии APCI 0.5.1.0 (PTT 2.8.150), то большая часть значений будет не найдена. Если же смотреть в ДевТуле на базы APCI 0.7.1.0. (PTT 2.8.130), то все значения есть. проверял у себя.

p1kkp Enables OBD Information that can be used for all variants T2P_ChO-002732 [0] = EM-EC01 [1] = EM-EC06 [2] = EM-EU5 [3] = EM-EU6 [4] = EM-JPN10 [5] = EM-JPN16 [6] = EML8 Note: EM-EC01 = European Community 2001 Level Euro 3 EM-EC06 = European Community 2006 Level Euro 4 EML8 = Special Customization of Euro 6 for Japan ChO for ENUM[6] = EML8 Change is ChO-11461..

p1scm NOX Control, Diagnostics. Indicates current status of Nox Control Diagnostics. 0- No Warning, 1 – Nox control device removal warning, 3- maf sensor removal warning.

p1rn6 Nox Control System

p1ak1 Adblue Bargraph In Display Used to completely enable / disable the AdBlueBargraph in the display. Vehicle without AdBlue must deactivate this parameter. true = Bargraph visible false = Bargraph hidden

p1e37 Emission Standard Emission Standard coding as follows: n = Euro n for example: 5 = Euro V 6 = Euro VI

p1eoe Malfunction Indication Telltale For On Board Diagnostics Enabled Indicates if the malfunction indication telltale function for on board diagnostics is to be enabled or not. False = Disabled True = Enabled ReadWrite

p1awx ECUList Aftertreatment Control Module installed Defines if he ECU is installed ReadWrite

p1alz Fuel Consumption, Calibration In Percent A percentage correction value to compensate any deviation between the calculated fuel consumption shown in the Driver Information Display and the fuel consumption according to the customer's fuel protocol. A value up to +/-10% can be programmed. For example the value 2 means an increase of 2% and -2 a decrease of 2%. The following formula gives the new value of P1ALZ to program: P1ALZcurrent + C = P1ALZnew. Example: (P1ALZcurrent = -3) + (Factor C = 4) = 1 = P1ALZnew i.e. if current parameter value is -3 and factor C is 4 then the new parameter value to program is 1. NOTE -- For US markets which uses miles per gallon (mpg) as standard fuel consumption unit, please use fuel consumed in gallons in the equation, instead of mpg in the above equation. The following formula gives the correction factor C: (Consumption according to the customer's fuel protocol - Consumption according to display) / Consumption according to display x 100 = the correction factor C. Example: (3.612 - 3.487) / 3.487 * 100 = C = 3.58% The correction factor C should be rounded off to the nearest integer, i.e. 3.58% should be rounded up to 4%. Note: When the programming operation of P1ALZ is complete, reset the Trip and fuel data in Driver Information Display.
p1e5q OBD Torque Limiter Enabled Enables OBD (On Board Diagnostics) torque limiter functionality. 0 = OBD Torque Limiter Functionality Disabled 1 = OBD Torque Limiter Functionality Enabled

p1fox Engine Emission Standard Defines the engine emission control standard. [0] = EM-EC01 [1] = EM-EC06 [2] = EM-EU5 [3] = EM-EU6 [4] = EM-JPN10 [5] = EM-JPN16 [6] = EML8 Note: EM-EC01 = European Community 2001 Level Euro 3 EM-EC06 = European Community 2006 Level Euro 4 EML8 = Special Customization of Euro 6 for Japan ChO for ENUM[6] = EML8 Change is ChO-11461.. ReadWrite

p1dt6 AdBlue Level Function Enabled Availability of the AdBlue Level function. false = function not available true = function available ReadOnly
p1d4t AdBlue Level Low, Function Defines if the "AdBlue Level Low" function is available. BD 4.2.8.3.12 AdBlue Level Low It shall be possible to enable or disable the AdBlue Level Low function separately from the AdBlue Level function. Values: FALSE = function not available, TRUE = function available Default value: TRUE. ReadWrite

p1e7r Coolant Temperature Set Point ReadWrite

p1ask Warm Hold, Function Enable/disable the warm up and warm hold function. The warm hold function is automatically engaged at idle in order to provide faster engine warm up. ReadWrite

p1c1t OBD Failure Alert Event Logging, Enable Enables logging of OBD failure alert events. ReadWrite

p1c0p AdBlue Tank Low Level Event Logging, Enable. Enables logging of AdBlue tank low level events. ReadWrite


А это инфа ( не проверенная) с сайта автоэлектриков. Вольво FM и FH4 версия отключения девтулом ( только английская версия), но если стоит эмулятор то он должен быть снят и восстановлена проводка на блок Адблю.

p1e5o. Max torque limiter Ratio. Max torque, in procent of ratedtorque, when the limiter apples.