MAN EOL Программирование

bazuka

.......

ATTENTION !!!
Make sure when doing programming, use computers with the same type of flash memory !!! (ex.: Fash 2001 = 256 kb RPF, RPF 2004 = 512 kb)

First of all,
there are four stages to successfully change almost any computer with MAN offline programming tool.

-a little bit of willpower.

That said, let's get to work.

STAGE I

Ignition ON, engine off.

Step 1 - Select Vehicle programming - V
Step 2 - check If the conditions of note is fulfilled - V
Step 3 - Parameter settings - V
Step 4 - Parameter settings with vehicle data file when exchanging the control unit -V
Step 5 - If dialog to connect interface appears - V
Step 6 - from vehicle to management computer - V

At this moment MAN CATS start downloading data from the FFR in computer as a vdf file.

Step 7 - on next dialog window a lists with vehicle computer are shown. Select back - V
Step 8 - exit parameter settings - V
Step 9 - End vehicle programming - V


STAGE II

Step 1 - open MAN EOL file edit
Step 2 - from menu select File + Open from MANCATS
Step 3 - on open dialog window select "Files of type:" who opens the .vdf file type
Step 4 - select the file which corresponds to the serial number of vehicle
Step 5 - on File menu select Save to MANCATS
Step 6 - on message box press ok


STAGE III

Step 1 - Select Vehicle programming - V
Step 2 - check If the conditions of note is fulfilled - V
Step 3 - Parameter settings - V
Step 4 - Flash Programming/Parameter settings with conversion - V
Step 5 - from service computer:From HDD - V
Step 6 - Select file with serial number you have saved -V
Step 7 - Perform Conversion (or perform entire conversion again) - V

At tis moment MAN CATS check and compare data from FFR and the file for programming.

Step 8 - Use date from HDD - V
Step 9 - in Apply for password dialog - select By fax with vehicle
Step 10 - select YES - V
Step 11 - on Fax form for password - V
Step 12 - Ignition OFF - V
Step 13 - Change the unit
Step 14 - Ignition ON - V

At this time MANCATS compare data and if any discrepancies appear, in next window are shown all differences between FFR data and file data.

Make a printscreen of differeces an send it to me along vdf file that you downloaded fom FFR (you can find it on C:\MAN cats II\Runtime\VDF\)

I will send you the modified files for STAGE IV as fast as I can.

STAGE IV

For this stage you need all vehicle keys for programming and start MAN Immo calc.exe

Step 1 - Select Vehicle programming - V
Step 2 - check If the conditions of note is fulfilled - V
Step 3 - Parameter settings - V
Step 4 - Flash Programming/Parameter settings with conversion - V
Step 5 - from service computer:From HDD - V
Step 6 - Select file with serial number you have saved -V
Step 7 - Perform Conversion (or perform entire conversion again) - V
Step 8 - Use date from HDD - V
Step 9 - in Apply for password dialog - select By fax with vehicle
Step 10 - select YES - V
Step 11 - on Fax form for password - V
Step 12 - Ignition OFF - V
Step 13 - Change the unit
Step 14 - Ignition ON - V
Step 15 - On unit list for programming select FFR unit and the unit that you changed it - V
Step 16 - use data from HDD - V
Step 17 - On immobiliser key - V
Step 18 - Immobiliser delete key? YES - V
Step 19 - Fax password - V - V - YES - V
Step 20 - V
Step 21 - Assignment of vehicle correct - v
Step 22 - on Password immobiliser [] window, switch on MAN Immo calc program, press Pass button and write the password generated between[ ](ex.[0123456789])
Step 23 - Password correct - V
Step 24 - on Immobiliser delete key window - YES - V
Step 25 - A total 1 key(s) has now been learned - V
Step 26 - If you heve more than 1 key select YES - V ; if you have just one key jump to step 30
Step 27 - Ignition OFF - V
Step 28 - wait 15
Step 29 - change key, Ignition ON - V
For another key(s) repeat steps 226-29
Step 30 - Ignition OFF - V
Step 31 - wait 15
Step 32 - Innition ON - V
Step 33 - on The immobiliser is already active windw - V
Now yo have to wait some time
Step 34 - Parameter settings procedure...bla-bla - V
Step 35 - V
Step 36 - You have sucsessfully set the .... bla-bla -V
Step 37 - Maximum speed limiter window - V
Step 38 - Perfor a test message - V
Step 39 - select Clear all diagnistic memories - V; after clear -V; select END - V
Step 40 - Start Engine

THE END OF PROGRAMMING

Take into consideration a clutch calibration.


правда одну строчку в расчёт можно не брать. с отправкой vdf

__________________
Вот как надо строить мосты, МинСтрой такого и не видел!!!!


Для просмотра ссылок или изображений в подписях, у Вас должно быть не менее 10 сообщение(ий). Сейчас у Вас 0 сообщение(ий).